Picture of LGB-28, Block Ovens

LGB-28, Block Ovens

28 Hole Oven shown with water cooled condenser for ASTM oil immersion tests.

Specifications

Test-Tube Capacity	28
Height	14.5 in
Temperature Range	100 to 500 ºF
Voltage	220 V
Power	3000 W
Temperature Control	P.I.D. digital
Phase	1
Weight	355 lb
Standard	ASTM D-471 for liquid effects ASTM D-865 for air heating
Accessories	Glassware for Block Ovens A major disadvantage to the present systems of oil immersion testing is the evaporation of volatile fluids. The test must also be carried out in explosion proof enclosures. The Benz water cooled reflex condenser reduces the need for constant monitoring of liquid levels as well as the hazardous build-up of volatile gases. Benz Materials Testing Instruments has in stock all aluminum block aging oven accessories to perform ASTM D-471 and D-865 for rubber deterioration. ASTM D-471 for Liquid Effects LGB-24: 38 mm x 300 mm test tubes LGB-25A: Single-hole stoppers LGB-27A: 15 mm reflux tube LGB-92: Water-cooled condenser LGB-93: Condenser test tube ASTM D-865 for Air Heating LGB-24: 38 mm x 300 mm test tubes LGB-25: Two-hole stoppers LGB-26: 9 mm short vent tube LGB-27: 9 mm long vent tube
Features	Cross-contamination of samples is eliminated by use of up to 28 individual test stations. Solid-aluminum block is cleaner and safer than oil baths, and transfers heat at a faster rate. Round design provides a more constant and uniform heat transfer than square block ovens. Up to three inches of insulation surrounding the block prevent loss of heat and reduces electrical consumption during long-term aging studies. P.I.D. temperature controllers maintain a constant temperature without drifting above or below set point. Stainless steel jacketing eliminates corrosion caused by spills of test fluids Preset high-limit switch shuts off power if overheating occurs. Both ASTM D-471, for liquid aging, and D-865, for air aging, can be run at the same time. The system can be set up, with the water-cooled reflux condenser, to reduce constant monitoring of liquid levels and build-up of volatile gases.

LGB-28, Block Ovens

28 Hole Oven shown with water cooled condenser for ASTM oil immersion tests.

Test-Tube Capacity	28
Height	14.5 in
Temperature Range	100 to 500 ºF
Voltage	220 V
Power	3000 W
Temperature Control	P.I.D. digital
Phase	1
Weight	355 lb
Standard	ASTM D-471 for liquid effects ASTM D-865 for air heating
Accessories	Glassware for Block Ovens A major disadvantage to the present systems of oil immersion testing is the evaporation of volatile fluids. The test must also be carried out in explosion proof enclosures. The Benz water cooled reflex condenser reduces the need for constant monitoring of liquid levels as well as the hazardous build-up of volatile gases. Benz Materials Testing Instruments has in stock all aluminum block aging oven accessories to perform ASTM D-471 and D-865 for rubber deterioration. ASTM D-471 for Liquid Effects LGB-24: 38 mm x 300 mm test tubes LGB-25A: Single-hole stoppers LGB-27A: 15 mm reflux tube LGB-92: Water-cooled condenser LGB-93: Condenser test tube ASTM D-865 for Air Heating LGB-24: 38 mm x 300 mm test tubes LGB-25: Two-hole stoppers LGB-26: 9 mm short vent tube LGB-27: 9 mm long vent tube
Features	Cross-contamination of samples is eliminated by use of up to 28 individual test stations. Solid-aluminum block is cleaner and safer than oil baths, and transfers heat at a faster rate. Round design provides a more constant and uniform heat transfer than square block ovens. Up to three inches of insulation surrounding the block prevent loss of heat and reduces electrical consumption during long-term aging studies. P.I.D. temperature controllers maintain a constant temperature without drifting above or below set point. Stainless steel jacketing eliminates corrosion caused by spills of test fluids Preset high-limit switch shuts off power if overheating occurs. Both ASTM D-471, for liquid aging, and D-865, for air aging, can be run at the same time. The system can be set up, with the water-cooled reflux condenser, to reduce constant monitoring of liquid levels and build-up of volatile gases.

LGB-28, Block Ovens

Picture of LGB-28, Block Ovens

28 Hole Oven shown with water cooled condenser for ASTM oil immersion tests.

Test-Tube Capacity	28
Height	14.5 in
Temperature Range	100 to 500 ºF
Voltage	220 V
Power	3000 W
Temperature Control	P.I.D. digital
Phase	1
Weight	355 lb
Standard	ASTM D-471 for liquid effects ASTM D-865 for air heating
Accessories	Glassware for Block Ovens A major disadvantage to the present systems of oil immersion testing is the evaporation of volatile fluids. The test must also be carried out in explosion proof enclosures. The Benz water cooled reflex condenser reduces the need for constant monitoring of liquid levels as well as the hazardous build-up of volatile gases. Benz Materials Testing Instruments has in stock all aluminum block aging oven accessories to perform ASTM D-471 and D-865 for rubber deterioration. ASTM D-471 for Liquid Effects LGB-24: 38 mm x 300 mm test tubes LGB-25A: Single-hole stoppers LGB-27A: 15 mm reflux tube LGB-92: Water-cooled condenser LGB-93: Condenser test tube ASTM D-865 for Air Heating LGB-24: 38 mm x 300 mm test tubes LGB-25: Two-hole stoppers LGB-26: 9 mm short vent tube LGB-27: 9 mm long vent tube
Features	Cross-contamination of samples is eliminated by use of up to 28 individual test stations. Solid-aluminum block is cleaner and safer than oil baths, and transfers heat at a faster rate. Round design provides a more constant and uniform heat transfer than square block ovens. Up to three inches of insulation surrounding the block prevent loss of heat and reduces electrical consumption during long-term aging studies. P.I.D. temperature controllers maintain a constant temperature without drifting above or below set point. Stainless steel jacketing eliminates corrosion caused by spills of test fluids Preset high-limit switch shuts off power if overheating occurs. Both ASTM D-471, for liquid aging, and D-865, for air aging, can be run at the same time. The system can be set up, with the water-cooled reflux condenser, to reduce constant monitoring of liquid levels and build-up of volatile gases.